How to choose a laundry tub (a handyman’s guide)

Most laundry tub problems I see start in the shop, not on install day. The tub is too big for the space, the taps don’t suit it, or it arrives on a pallet and nobody has worked out how to get it inside. This is the checklist I run through before anyone buys one.

Replacing a laundry tub in a rental or strata unit

A like-for-like swap can usually be done in one visit. Tenant access is arranged with the manager or agent beforehand, and the old tub is taken away. Before and after photos are taken, and the invoice goes straight to the agency.

Stainless steel is the better choice for rentals, because it lasts between tenants. A standard size also makes the next swap easier down the track.

For shops and cafes, this also covers back-of-house tubs and cleaner’s sinks, swapped quickly so they keep trading.

Measure first

Start with the space, not the tub. Write down the numbers before you look at anything.

  • Width, depth and height of the spot, allowing for skirting and wall lining. A rim height around 900 mm is common, but go by whoever uses it most.
  • Waste position: where it comes out of the wall or floor, and how high.
  • Tap position: where the hot and cold taps are now, or will be.
  • Washing machine: if it sits beside the tub, allow room for the hoses, room to pull it out, and space for its lid or door to open.

Take a photo of the wall with a tape measure in it. It saves a lot of guessing later.

Size: 30L, 35L or 45L

Tubs are sold by capacity. A 30L tub suits a tight laundry where it mostly handles hand washing and the odd mop bucket. A 35L is a sensible middle size. A 45L is the roomiest of the three and copes with a big bucket or bulky items, but it takes the most space.

A double bowl is worth it if you have the wall run for it, since it is much wider than a single. It helps if you often soak in one side and rinse in the other. If you don’t, a single bowl with a bench beside it does the job for most households.

Tub with cabinet or inset sink

Tub with cabinet. One unit: the tub, a cabinet underneath and usually doors. It suits a standard laundry where you want storage and a tidy finish. It is generally the easier install, because there is less to build. The cabinet needs a level floor, and it may need a cut-out at the back for the pipework.

Inset sink. The sink drops into a bench you already have or build. It suits a custom laundry, or one where the bench matches the other cabinetry. It is more work: the cut-out has to match the sink’s template, the edges need sealing, and the bench has to carry the weight of a full bowl.

If you are replacing an old tub in the same spot, a like-for-like swap is usually the least trouble.

Stainless steel or poly

Check what both the tub and the cabinet are made of.

Stainless steel wipes clean, handles knocks and doesn’t mind hot water. It can show scratches and water marks, and a cheap grade can rust at the cut edges in a damp or coastal laundry. A decent unit should last for many years.

Poly (plastic) won’t rust and is light to carry. It can stain, scratch and sag under heavy loads, and it may yellow near a sunny window. It cleans with ordinary detergent, but expect it to wear sooner than good stainless. Weigh the budget against how hard the tub will be used.

Taps and waste

Tap hole or wall tap. Some tubs have a tap hole for a tap mounted on the tub. Others have none and expect a wall-mounted tap. Choose the tap and the tub together, and check the number and size of the holes suit the tap you want.

Bypass holes. If the tub has a bypass or overflow hole, the waste has to suit it, or it can leak.

The trap. It needs room under the tub and has to line up with the waste in the wall or floor. Check there is enough height, and that you can still reach it later.

The mistakes I see most:

  • Buying the tub before checking where the waste sits.
  • Tap holes that don’t match the tap.
  • No access to the trap once the cabinet is in.
  • Forgetting the washing machine hoses and taps.
  • Not sealing the edge between the tub and the wall.

Show whoever is doing the plumbing the tub and taps before you buy.

Managing a rental or strata building? Send a work order and we’ll handle the swap, tenant access and photos.

Doing your own laundry? Get a quote

Licence 386984C – fully insured – Trusted by stores including Gong Cha and Chatime.

iWill Handyman in white polo shirt beside a newly installed laundry tub and taps in a bright Sydney rental apartment

Getting it home

Tubs and cabinets are bulky, and some are heavy. Before you order, measure the path from the front gate to the laundry, including doorways, stairs and tight corners.

If it is being delivered, ask whether it comes to your door or the kerb, and whether it arrives assembled or flat-packed. Check it for dents and cracks as soon as it arrives. If you are picking it up, take a ute or van and a second person, and tie it down. Keep the packaging until the job is finished.

Where I buy mine

For laundry tubs and sinks I usually go to OTC Tiles & Bathroom in south-west Sydney. They keep the common sizes in stock and have a showroom where you can see them.

Managing a rental or strata building? Send a work order and we’ll handle the swap, tenant access and photos.

Doing your own laundry? Get a quote

Licence 386984C – fully insured – Trusted by stores including Gong Cha and Chatime.

Laundry tub replacement questions

How long does a laundry tub replacement take?

A like-for-like swap in the same spot is usually the quickest option. More time may be needed if the waste, taps or cabinet need adjusting.

Can you arrange access with the tenant?

Yes. For rentals and strata units, access is arranged with the property manager or agent before the visit.

Do you remove the old tub?

Yes, the old tub is taken away as part of the job.

Stainless or poly for a rental?

Stainless steel is generally the better choice for rentals, since it holds up well between tenants.

What size laundry tub do I need?

It depends on the space and how the tub is used. Measure the spot first, and check the waste and tap positions line up, as covered above.

Scroll to Top